Cable Management Solutions is engaged primarily in the design and manufacture of cable management products providing designers and installers with a "total solutions" package for the distribution of lighting, power, data, voice and control services throughout new and refurbished office buildings. The company was formed as a result of extensive market research and its acquisition of a clear understanding of customer requirements, both technical and commercial.

A typical solutions package offered by Cable Management Solutions would include any or all of the following product ranges: -

• Modular Wiring Systems (Power, Lighting, & Comms)
• Floor Outlet Boxes
• Service Access Grommets
• Steel and Moulded Desk Modules (Power & Comms)
• Underfloor Busbar Systems
• Distribution Systems for solid floors
• Bespoke Cable Management Systems (Power, Lighting & Comms)

itsa™ Modular System (Power, Lighting & Comms)

The itsa™ Modular System is offered in Power, Lighting and Communication systems. Power and Lighting can be supplied in a fully encapsulated steel versions as well as the standard plastic with LSF cable.
The system is easy and quick for ease of installation and is based on the tried and tested ‘plug and play’ principle with snap together retained connectors. With minimum wiring on site the system gives a very cost effect method of distribution for Power, Lighting and Data.

itsa™ Floor Boxes

The itsa™ Floor Box is quick fitting with a unique latching mechanism that provides a quality product with low installation costs. Both the 3 and 4 compartment formats fit within a common panel cut out of 300mm x 200mm. Reversible lid/trim assembly is manufactured from flame retardant ABS and has two cable exit flaps providing 60mm x 15mm openings.
The accessory plates can be offered to suit most of the Power, Data and Communication requirements of the modern office environment.

Cableway 1000 Service Access Grommets

Cableway 1000 provides an economical solution to the
distribution of Power, Data and Communication services within raised access floors. The selection of 1, 2 or 3 cable exits enables varying cable capacity. Utilising all three openings facilitates up to 6 x 20mm conduits, or a combination of 3 x 25mm and 3 x 16mm diameter conduits. Unique spring clips allow ease and speed of installation and is aesthetically pleasing in appearance.

Steel and Moulded Desk Modules (Power & Comms).

Desk Modules can be offered from our standard range in 2 gang, up to 12 gang units. Housings can be supplied in Metal, Aluminium or Plastic with the unit complete with 3 metres of 1.5 mm square 3 core PVC cable and wired to a standard 13amp fused plug.
Bespoke units can be offered encompassing your individual requirements please do not hesitate to ask our dedicated sales staff for assistance.

itsa™ Track Underfloor Busbar Systems.

The itsa™ track busbar system has a modular 300mm socket pitch that allows the ease of movement once installed. This gives great flexibility to the end client for any expansion or alteration to his original office layout.
itsa™ Track Underfloor Busbar System is a modular 3 or 4 bar busbar system rated at 63amps 240 volts. Each modular length of busbar is fitted with 3 or 4 pin shuttered socket outlets at 300mm intervals as standard.

Distribution Systems for
Solid Floors

We offer a range of trunking systems suitable to be installed into screeded solid floors. Flush Screeded systems and Buried systems are 3 compartment allowing distribution to Power, Data and Communications and have access boxes at suitable intervals. The system has the relevant junction boxes, end stops and risers etc to complete the system.

Bespoke Cable Management Systems (Power, Lighting & Comms)

Our expertise has been sought by a number of high profile clients to produce bespoke units such as shown in this illustration. From concept to design, specification and then through manufacture and supply our many years of expertise by our dedicated team are able to guide you through this process to a successful quality product.
The unit comprised of a purpose built designed steel housing having 6 x MCB’s, 1 x switch disconnector, which were protected from accidental switching by a hinged polycarbonate cover. A 3 metre nylon conduit and BS4343 plug was wired to the unit. All internal wiring complied with the relevant IEE regulations. The outgoing power was by 6 x 4 pole connectors.